top of page


  • Excellent (cold) water solubility
  • Improved thermal stability, resulting in less risk on deterioration/crystalizing inside the nozzle
    • Max thermal stability of 225° C, tested up to 256 seconds with no flow
  • Biodegradable once dissolved in water
    • Safe dissolution in tap water
    • Can be disposed of in the kitchen sink, or household drain with an excess of water
  • Good bonding to PETG-based materials and other (thermo)plastics that print within a similar temperature range
  • Less sensitive to deterioration by humidity compared to regular PVA



  • Reliable multi-extrusion 3D printing of complex structures that require a water-soluble support material
    • 3D printing geometries with large overhangs, or complex hollow structures
  • PVA molds


General printing guidelines*

  • Spool Weight: 0.3kg
  • Nozzle size: ≥ 0.15mm
  • Layer height: ≥ 0.1mm
  • Print temp: ± 180 - 210° C *
  • Fan speed: 0 - 30%
  • Heat bed: ± 0 - 60° C
  • Enclosure needed: No
  • Experience level: Expert


*)Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

*) Do not exceed a printing temperature of 225˚C, because AquaSolve PVA will then crystallize to quickly and it will no longer flow and/or dissolve in water.Printing with PVA materials does require a certain level of 3D printing expertise as PVA cannot stay too long in the hot secondary/support nozzle and needs to flow and by that needs expert tweaking to find the optimal “waiting temperature” for the material not to deteriorate/crystalizing in the hot secondary/support nozzle when not being 3D printed.


General guidance for printing with PVA support materials

Printing with PVA, in general, isn’t plug and play and does require a fair amount of 3D printing expertise as there isn’t a generic one-size-fits-all setting for dual extrusion printing with PVA materials. The optimal PVA settings can even vary between the same models of 3D printers.


One of the most common challenges are to establish a good bond between the PVA support material and the primary building material. Below parameters are of utmost importance to establish good adherence.

  • Verify the extrusion distance between the printed object and the PVA support.
    • The default setting in most slicer software is often set at a distance of 0.1mm or 0.2mm, which works well for break-away support, but not for PVA support.
    • For PVA support materials the extrusion distance must be set to 0.0mm as both materials must really come into contact with each other.
  • The printing (nozzle) temperature is extremely important and it is advised to measure the actual temperature of the nozzle and to compare this temperature with the temperature set in the print settings.
    • If the actual temperature of the nozzle is for instance 10° C lower than the temperature in the print settings it might very well be that the layer of PVA support material is not flowing optimally into the layer of the primary building material. It is often seen that the actual nozzle temperature varies from the print temperature set in the slicing software.
  • Verify if the nozzles of your printer are properly leveled and have exactly the same height so that there is no “height difference” when layering the PVA support material on top of the primary building material.
    • In order to verify this it is recommended to 3D print a 5cm x 1cm rod and to print every 1 to 2 layers with the left nozzle and the following 1 to 2 layers with the right nozzle and to repeat this process multiple times.If you notice a non-perfect layering then the nozzles aren’t properly leveled.This process can be done with PLA for instance.

Formfutura 1.75mm Atlas Support™ (PVA)

  • Atlas Support is a water-soluble PVA (polyvinyl alcohol) support material for complex multi-extrusion 3D printing with PETG based materials. Atlas Support is a 3D printer filament with improved thermal stability and can be 3D printed at slightly higher temperatures compared to regular PVA. This makes Atlas Support an ideal PVA support material for PETG-based materials with good thermal and chemical adherence.

Related Products